With the dividends of the picnic bench being enjoyed, now was the time to partly enclose the space with the rock wall. This rock wall would enclose the back face of the Jungle Fort and also provide a wind break. Our property is fortunate to be only one and a half miles from the ocean and at around eleven o’clock each day the wind picks up and there is a steady breeze. This is a great relief during the summer months but as the season changes and the winter months approach it can get a little chilly so this rock wall will provide a welcome refuge for my children when they sit at the picnic bench.

I had decided to split the vertical rock wall so that it had a high section and a lower section, by doing this it would satisfy both my childrens skill levels and also provide an easy access to the back of the fort platform. The plans had provided both a vertical wall and a sloped climbing wall but as our space was just with six feet of clearance from the vertical wall, an angled alterative was out of the question. Continue reading Jungle Fort Vertical Rock Wall →

Finishing all the main players on the Jungle Fort has certainly taken many of my weekends but the satisfaction of this construction shows on my childrens face every time they play on it. The one main outstanding item that is missing is the climbing wall but this can only be installed after I’ve fitted the picnic bench.

I had already cut to size the pressure treated lumber rather than using the WPL (wood polymer lumber) so as to keep the look consistent. This would be used for the seats and the table top. The first phase of the installation would be to secure the supports for the seats and the table top to the uprights of the Jungle Fort. These supports would be secured by 5 inch by 3/8 inch galvanized lag bolts. I had decided to counterbore the position of these bolts so that the head would not be protruding from the material after tightening, even though it would only be by a small amount. The instuctions only called for the lag bolts to be fastened into position. I later found out why, with the counterbore the lag bolt would be tightened and it would burst through the other side of the upright. this would entail cutting off the offending point with a hacksaw and then filing flush with the timber. This was an unfortunate oversight by myself but the end result left no sharp edges, it was additional work but I was pleased with the result. Continue reading Picnic Bench and Lunch! →

My big push is on to erect the next stage of the playset, this stage should go reasonably fast as all the preparation has already been done. I’ve already installed the additional upright that the Monkey Bars will bolt on to, the only additional item is to drill the main corner upright for bolting the left upper rail of the Monkey Bars to the Jungle Fort.

The length of the Monkey Bars from the Jungle Fort is eight feet with a height of just over seven feet. This gives a good workout for my son who just loves the Monkey Bars, even though as a three year old he had an accident that resulted in eight staple stitches being used to close up a gash in his head. This accident was the result of him trying to do the Monkey Bars at his pre-school group, he would persist in trying to get across to the other side and slipped, hitting his head on the step. Fortunately my wife was at hand to take him to the closest emergency medical center. This mishap had not phased him at all, in fact he’s more determined than ever, the very next week he was back on the bars.

In my previous post on my series of constructing the Jungle Fort I spoke about the discrepancy with the slide that was ordered with the main hardware back in April of this year. It was only when I started to assemble the slide that it dawned on me that the slide was in fact different to the one that we ordered. With that knowledge I emailed the company Detailed Play Systems together with images of the slide together with the original order email from April 21st 2007, the email I sent was dated September 18th 2007, nearly five months after the fact. Continue reading Detailed Play Systems come up Big →

With the safety on top of the decking pretty much assured now, my main focus was to enable the children to be able to get up there. I had earlier on decided to eliminate the ladder configuration and replace it with a ramp, I felt that this would be more in line with the theme that they would use the structure for, a pirate enclave as such. We had saved the pirate flag that Jackson had made for the previous swingset, it was from one of my old black T-shirts. He had painted with my help a yellow skull and crossbones on it and this would be reattached to the new fort after everything was done. The marketing from the Pirates of the Carribean together with all the paraphernalia that goes with it had sparked his desire to make his own flag. Once finished it had been flying from the old swingset for over a year before we had to dismantled it. Although looking a bit tired I’m still surprised that it’s in reasonably good condition but a repaint will certainly spruce it up again.

The ramp material had already been precut, sanded, coated with green preserve and then coated with redwood stain. The first test for me was to collect all the labeled parts for the ramp from the remaining pile of lumber. There had been a vast change in the size of the pile because a good deal of the material had already been assembled but there was still enough left to make it awkward. The two main rails were laid out on the lawn as this was the only place that was free enough to maneuver the length, together with the slats that would line the inside of rails and act as a support for the boards that would be the gangplank. Continue reading Ramp Up to the Jungle Fort, Slide Down →

The success of erecting the swing beam with swings and hardware paid dividends during the week while I was at work. My children had plenty of playtime testing out the new swings with my young daughter pleading to her brother to push her on her swing, gone was the baby swing as she was a “big girl now.” No mention had been made of putting up the previous baby swing as her new “blue” colored swing gave her the additional thrill of being able to go higher, meanwhile you could hear the cries from her mother, “not too high” ringing from the house.

The task for the weekend was to progress the safety of the decking by erecting the walls. Even though there would be numerous openings for the Monkey Bars, Rock Wall, Slide and Ramp, the remaining openings would have to be filled. The most difficult aspect was to reconfigure the upright supports that would provide support for the cross members. The back wall would be split between a high and a low Rock Wall, I would have to start there with a cross member first. The cross member would span across the back face with a gap of 14 inches between the decking and the bottom of the rail allowing enough room to crawl in from the lower Rock Wall with a hand grip providing additional safety. This part had already been cut, predrilled and coated with redwood stain making it an easy installation. I had also cut enough upright rails that would span the whole back face but as I had decided to do a split level Rock Wall I would also need to install a fixed upright at the center point of the decking to support the boards that would make up the higher Rock Wall. Continue reading Wall-In the Decking and Roof Frame Construction →